How To Repair Holes In Vinyl Siding
Vinyl siding installation should be left to the pros unless you're confident that you have adequate carpentry skills and feel. The upside of doing the projection yourself is that you tin can cutting the cost of installation to almost half of what yous will likely shell out to rent a contractor. The installation of vinyl siding itself is non that hard, but it does require proper planning equally well as precise measurements, calculations, cuts and leveling to ensure that the panels fit your wall perfectly.
The steps for vinyl siding installation below assume that you have completed installing the panels for the soffit, which is the underside of the roof overhang, and the fascia, which is the horizontal band forth the bottom of the roof. For this projection, yous volition need the following tools:
Power saw Hammer Tin snips Utility knife Record mensurate Chalk line Level Ladder
Apart from vinyl siding panels, the other needed materials are:
Starter strips J-trims Corner moldings Utility trims Drip caps Housewrap and A lot of nails, preferably those with wider heads Plywood
Keep in mind that even many pros adopt not to have this job on alone. Have one or two friends help y'all. In one case you accept all tools and materials listed to a higher place, you lot're ready to take on this vinyl siding installation DIY.
Step Remove Obstacles
Articulate the wall of anything that volition make it the fashion of the vinyl siding such equally exterior lamps, retractable clothesline spools, address plates or old vinyl sidings. Plan the disposal of your old siding properly. Don't mess with utility fixtures or the electric meter. You need to work effectually them.
Take Measurements
Measure from the eave downwardly to the lesser where you lot'll nail the starter strip. Most vinyl sidings are 12 feet long and eight inches broad. This ways that if the distance between the eave and the bottom is divisible by viii inches, you tin connect your top console directly to the J-trim. Well-nigh of the time, however, you volition have to modify your final acme console and utilize a utility trim to install this last piece.
Detect Your Level Points
Find the level points at the bottom for the starter strip and marker them with the chalk line. Try to be as precise as possible with the level points. This will make the task easier as you lot commencement installing the vinyl siding.
Attach the Starter Strip and Vertical Trims
Align the starter strip carefully forth the chalk line and nail it firmly to the wall. Blast iii ½ inch by ½ inch plywood pieces along the top of the starter strip to make information technology sturdier and help it hold upward the vinyl siding panels. Adjacent, attach the vertical trims, including the corner posts and end channels. You may also adhere the trims around the windows and doors at this point.
Cut the Vinyl Sidings According to Length
Mensurate the distance between the vertical end posts and cut the vinyl panels according to length for each row. Permit for a ¼ inch altitude between the stop of the siding and the corner mail service. Increase the distance to ⅜ inch in areas where the temperatures get every bit low as 40 degrees Fahrenheit. Vinyl siding expands and contracts along with temperature fluctuations. The gap will prevent damage to the siding.
Install the Vinyl Sidings
Sheath the first few anxiety above the starter strip with the insulation or wet protection fabric, and then snap and lock the first vinyl siding row on the starter strip. Nail the panels every maximum of 16 inches on the framing studs or furring on the wall. It is important to remember not to nail the vinyl sidings tightly confronting the wall and position the nail at the center of the slot; leave a 1/32 inch gap betwixt the blast head and the vinyl siding. You lot've installed each panel correctly if the siding can freely move from side to side. When you need to overlap panels to span a gap between posts, brand sure that the panels overlap by about an inch. Work your way upwards around the wall cutting around doors, windows and lamps using the tin snip.
Finish Upward
Every bit you lot reach the soffit on the eaves, mensurate the width that you need for the concluding piece in several locations and modify the vinyl siding panel according to the measurements. Install a J-channel. Make tabs on the cut edge of the console every half dozen inches using a snap lock dial. Install a utility trim into the J-channel. Lock in the last panel that you lot have modified on the terminal row and snap it into the utility trim on top of the wall.
Source: https://www.questionsanswered.net/article/how-to-install-vinyl-siding?utm_content=params%3Ao%3D740012%26ad%3DdirN%26qo%3DserpIndex
0 Response to "How To Repair Holes In Vinyl Siding"
Post a Comment